background image

www.insigniaproducts.com

6

60" Espresso TV Stand

Installation tips

Installing dowels

1

Put a drop of glue (

A

) in the dowel hole, then insert about 2/3 of the dowel (

B

 or 

E

) into the hole. You can tap the dowel 

with a rubber mallet, if necessary.

2

After the dowel is installed, wipe off the excess glue with a damp cloth.

Installing cam locks and cam screws

One end of a cam screw (

C

) is threaded, the other end is not. The un-threaded end locks into a cam lock (

D

 or 

F

).

1

Screw the threaded end of the cam screw (

C

) into the cam screw hole. 

2

Insert a cam lock (

D

 or 

F

) into a cam lock hole. Make sure that the open end in the cam lock faces toward the cam screw 

hole.

3

Insert the un-threaded end of a cam screw (

C

) into the opening in the cam lock.

4

Use a flat blade screwdriver to turn the cam lock clockwise until the arrow and the 

+

 and 

 symbols point away from the 

connected panel.

CAUTION: 

Make sure that you use glue with the dowels. The glue helps stabilize your TV stand and keeps it from coming apart.

CAUTIONS

:

• Do not use an automatic screwdriver to tighten the cam locks.
• Do not over-tighten the cam locks.

OR

1/3

OR

Summary of Contents for NS-HF2003






















Reviews: