background image

Generalities 

 

 

 

INOXPA S.A.U. 

20.025.30.01EN · (0) 2019/04 

2. Generalities 

2.1.  INSTRUCTIONS MANUAL 

This  manual  contains  information  about  the  reception,  installation,  operation,  assembly,  disassembly  and 
maintenance of the LR/LM side-entry agitator. 

Carefully read the instruction prior to starting the agitator, familiarize yourself with the installation, operation and 
correct use of the agitator and strictly follow the instructions. These instructions should be kept in a safe location 
near the installation area. 

The information published in the instruction manual is based on updated data. 

INOXPA reserves the right to modify this instruction manual without prior notice. 

2.2.  COMPLIANCE WITH THE INSTRUCTIONS 

Not following the instructions may impose a risk for the operators, the environment and the machine, and may 
result in the loss of the right to claim damages. 

This non-compliance may result in the following risks: 

  failure of important machine/plant functions, 

  failure of specific maintenance and repair procedures, 

  possible electrical, mechanical and chemical hazards, 

  risk to the environment due to the type of substances released. 

2.3.  WARRANTY 

Any warranty will be void immediately and lawfully and, additionally, INOXPA will be compensated for any civil 
liability claims submitted by third parties, in the following cases: 

  the service and maintenance work have not been carried out in accordance with the service instructions, 

the  repairs  have  not  been  carried  out  by  our  personnel  or  have  been  carried  out  without  our  written 
authorisation, 

  modifications have been carried out on our material or equipment without written authorisation, 

  the parts or lubricants used are not original INOXPA parts and products, 

  the material or equipment has been improperly used, has been used negligently, or has not been used 

according to the instructions and their intended. 

 
The General Conditions of Delivery already in your possession are also applicable: 
 

The machine may not undergo any modification without prior approval from the manufacturer. 

For your safety, only use original spare parts and accessories. 

The usage of other parts will relieve the manufacturer of any liability. 

Changing  the  service  conditions  can  only  be  carried  out  with  prior  written  authorization  from 
INOXPA. 

 

Please  do  not  hesitate  to  contact  us  in  case  of  doubts  or  if  further  explanations  are  required  regarding 
specific data (adjustments, assembly, disassembly, etc.). 

Summary of Contents for LM 1.10-4030-1-200

























Reviews: