manualshive.com logo in svg

Innovatech Teerminator-2000, Operation And Maintenance Manual

Share
Download
Innovatech Teerminator-2000 Operation And Maintenance Manual Download Page 32

INNOVATECH PRODUCTS & EQUIPMENT CO., INC. 

32

 

 
 

Trouble Shooting Guide 

Condition 

 

Probable Cause 

 

 

Corrective Action 

 

Cannot crank 

Discharged Battery 

 

 

Charge Battery or Replace 

 

Engine or 

Loose alternator belt 

 

 

Adjust 

 

 

 

Slow Cranking 

Ignition switch 

 

 

replace or repair 

 

 

 

starter 

   replace 

or 

repair 

  

 

charging system 

 

 

test; replace or repair 

 

 

 

Wiring 

   inspect 

   

 

 

 

 

 

 

 

 

 

Engine will 

No fuel in propane cylinder 

 

check and fill 

 

 

crank but will 

Propane cylinder valve turned off 

turn on 

 

 

 

not start 

No spark 

 

 

 

check coil, distributor, ignition switch 

 

Idle adjustment incorrect 

 

adjust 

 

 

 

 

Fast idle adjustment incorrect 

 

adjust 

 

 

 

 

 

 

 

 

 

 

 

 

Engine hesitation 

Idling adjustment incorrect 

 

adjust 

 

 

 

Improper idle 

Dirty carburetor 

 

 

clean 

 

 

 

 

Carburetor/ manifold gasket 

 

replace 

 

 

 

 

Improper tightening of Manifold/carburetor 

tighten 

 

 

 

 Carburetor 

plunger 

sticks 

 

clean 

 

 

 

 

 

 

 

 

 

 

 

 

Excessive fuel 

Idle adjustment incorrect 

 

adjust 

 

 

 

consumption 

Worn 

parts 

   service 

tune-up 

  

 

 

 

 

 

 

 

 

 

Overheating 

Radiator choked with dust 

 

Clean out air passage through fins with 

 

    low 

water 

or 

air 

pressure   

 

Loose fan belt 

 

 

tighten 

 

 

 

 

Internal restriction of radiator 

 

flush out 

 

 

 

 

dirty 

fluid 

   flush 

and 

replace 

  

 Inaccurate 

temperature 

gauge 

 

replace 

 

 

 

 

water pump failure 

 

 

replace 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Teerminator-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands