manualshive.com logo in svg

Innovatech Teerminator-2000, Operation And Maintenance Manual

Share
Download
Innovatech Teerminator-2000 Operation And Maintenance Manual Download Page 24

INNOVATECH PRODUCTS & EQUIPMENT CO., INC. 

24

 

LP-GAS 

Equipment Corporation

   

 

 

 

Main Office 

3216 S. Nordic Road 

Arlington Heights, IL 60005 

Telephone:  708-437-2345 

Telefax:  708-437-2350 

 

LP GAS EQUIPMENT CORPORATION 

WARRANTY 

 

LP GAS EQUIPMENT CORPORATION WARRANTS ITS PRODUCTS AGAINST DEFECTS IN 

MATERIAL AND WORKMANSHIP FOR A PERIOD OF NINETY DAYS.  DEFECTIVE 

MERCHANDISE WILL BE REPLACED WITHOUT CHARGE BUT LABOR CHARGES INCURRED IN 

THE REMOVAL, DISASSEMBLY OR REINSTALLATION OF SUCH PRODUCTS WILL NOT BE 

ALLOWED.  NO MERCHANDISE CAN BE RETURNED WITHOUT WRITTEN PERMISSION FROM 

THE FACTORY.  TRANSPORTATION CHARGES MUST BE PREPAID.  THE FACTORY SHALL BE 

THE SOLE JUDGE OF DEFECTS IN PRODUCTS RETURNED.  A TEN PERCENT HANDLING 

CHARGE WILL BE MADE FOR ALL MERCHANDISE RETURNED THAT IS NOT DEFECTIVE.  

ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.  WE RESERVE THE RIGHT TO 

LIMIT QUANTITIES AND TO MAKE PARTIAL SHIPMENTS UNLESS SPECIFICALLY 

INSTRUCTED OTHERWISE.  THE OBLIGATION OF THE COMPANY UNDER THIS WARRANTY IS 

LIMITED TO REPLACING ANY COMPLETE UNITS OR PARTS THEREOF WHICH BY OUR 

EXAMINATION WE JUDGE TO BE DEFECTIVE. 

NOTE:  FAILURES CAUSED BY:       DIRT 
              

 

 

POOR 

QUALITY 

FUEL 

                             ABUSE 
                               NORMAL WEAR 
                               DISASSEMBLY 
 
 
                 

ARE NOT COVERED BY OUR WARRANTY! 

Summary of Contents for Teerminator-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands