innovair QIN1129H2V31 Installation Manual Download | Manualshive

Page: 18 / 52

background image

18

8. Electronic Function

8.1 Abbreviation

T1: Indoor room temperature

T2: Coil temperature of evaporator

T3: Coil temperature of condenser

T4: Outdoor ambient temperature

T5: Compressor discharge temperature

8.2 Display function

8.2.1 Icon explanation on indoor display board.

Digital display:

Displays the temperature settings when the air

conditioner is operational.

Displays the room temperature in FAN mode.

Displays the self-diagnostic codes.

Dispalys ‘

’ for three seconds when Timer ON,

Fresh, Swing, Turbo or Silence feature is activated.

Dispalys ‘

’ for three seconds when Fresh,

Swing, Turbo or Silence feature is cancelled.

Dispalys ‘

’ under deforsting operation.

Dispalys ‘

’ when anti-cold air feature is

activated under heating mode.

Dispalys ‘

’ during self clean operation (if

aplicable).

Dispalys ‘

’ under 8

℃

heating operation (if

aplicable).

When ECO function(optional) is actived,the “

”

illuminates gradually one by one as

In one second interval.

NOTE:

A guide on using the infrared remote is not

included in this literature package.

8.3 Main Protection

©2015 Innovair Corporation. All Rights Reserved.

www.innovair.com

«
...
16
17
18
19
20
...
»

Summary of Contents for QIN1129H2V31





















































Reviews:

No comments

Related manuals for QIN1129H2V31

Brand: Lava Aire Pages: 15

Brand: Hamilton Beach Pages: 48

Brand: Daikin Pages: 16

PrecisionAire 225T Series

Brand: Flanders Pages: 5

TID-1800HP Type A

Brand: Toyotomi Pages: 12

Brand: GE Pages: 2

Brand: Rotenso Pages: 16

Brand: Zibro Pages: 18

Brand: Timberk Pages: 56

Brand: Acson Pages: 140

Brand: TCL Pages: 40

Brand: Hunter Pages: 24

Brand: Daikin Pages: 13

Brand: Daikin Pages: 36

Brand: Daikin Pages: 44

Brand: Haier Pages: 26

Brand: Haier Pages: 20

Smart PowerABH071H1ERG

Brand: Haier Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands