background image

INGICS

 ​

TECHNOLOGY

 

SSID is just like the above figure with part of the mac address. The default key to connect with it is 

“​12345678​”. You can change it later when you get into the web UI. 

After connection, enter IP address ​192.168.10.1​ in your browser. The default account/password 

are both “​admin​”. The following sections describe details of the web UI. 

Web User Interface 

You can review current configuration or modify it on the web UI. There are various function 

groups listed on the top of UI.  

 

Any change in  the page needs to be saved first before switching to another page, otherwise the 

modification will be lost. And after all changes made, click reboot to make the changes effective. 

 

System 

Display firmware and device information, including MAC address and IP address in station mode 

are shown here. 

Wi-Fi 

Users can configure iGS03M’s WiFi device as an WiFi AP or join to the other AP. The related 

settings can be managed on this page. 

AP Mode  

SSID:​ The default name is IGS03 plus 

the last digits of the mac address. 

Security: ​Open, WPA-PSK, WPA2-PSK 

and WPA-PSK/WPA2-PSK are 

supported. WPA2-PSK is 

recommended.  

Password: ​8-63 characters can be 

input  

Channel: ​1~11(ch12 and ch13 could be supported by request)  

 

 

         

 ​

INGICS TECHNOLOGY CO., LTD.    •    [email protected]    •    WWW.INGICS.COM 

  9 

Summary of Contents for iGS03M





















Reviews: