Ingeteam Ingecon Sun 100 Installation Manual Download Page 34 | Manualshive

Page: 34 / 72

Ingeteam Ingecon Sun 100 Installation Manual Download Page 34

AAS2000IKI01

24

Installation manual

Ingeteam Power Technology, S.A.

Turn the comms board so that the connectors can be seen.

Connector for J11

Connector for J12

Communications board, rear view

Connect the communications board exactly as shown in the following illustration.

J12

J11

5.4.9. Connection for ethernet communication

At the request of the installer, inverters may optionally incorporate hardware for communicating via ethernet. This
hardware is made up of an “AAX0004 Com Et RS-485” board.

The unit is provided with a 211 Ohm ferrite rod. The cable coming from the “AAX0004 Com Ethernet
+ RS-485” board (RS-485 output) must be inserted as close as possible to the board, turning it twice
around the hole at its centre.

The board is provided with a bag (attached with a plastic tie) containing the Ethernet cable. Connect the cable to the
board’s Ethernet output and feed it out through the holes on the upper left side of the enclosure.

See “AAX2002IKH01 Installation Guide for Communications Devices”.

Follow the same instructions given in the previous point for the connection of the board to the control board.

«
...
32
33
34
35
36
...
»

Summary of Contents for Ingecon Sun 100









































































Reviews:

No comments