Ingersoll-Rand MHP825WCAT Page 44 Operation & Maintenance Manual Download

Page: 44 / 109

Operation & Maintenance Manual

Operating Instructions

Operating Controls and Instruments

The operating controls and instruments are arranged on the control panel as shown above. A
description of each panel device is as follows:

Panel Light:

Illuminates the instrument control panel controlled by Switch 14.

High Compressor Temp:

Fault indicator lamp. Indicates shutdown due to high

compressor temperature.

Low Radiator Coolant Level:

Alarm indicator lamp. Indicates engine coolant

needs service.

Low Engine Oil Pressure:

Fault indicator lamp. Indicates shutdown due to low

engine oil pressure.

Restricted Air Filter:

Alarm indicator lamp. Indicates engine/compressor air

inlet filters need service.

High Engine Coolant Temp:

Fault indicator lamp. Indicates shutdown due to

high engine water temperature.

Summary of Contents for MHP825WCAT














































































































Search results

Summary of Contents for MHP825WCAT

Reviews:

Related manuals for MHP825WCAT

Brands by name

Popular brands

Ingersoll-Rand MHP825WCAT, Operation & Maintenance Manual

Search results

Summary of Contents for MHP825WCAT

Reviews:

Related manuals for MHP825WCAT

Brands by name

Popular brands