manualshive.com logo in svg

Ingersoll-Rand DOOSAN HP375WCU, Operation & Maintenance Manual, Page: 1 / 73

Share
Download
Ingersoll-Rand DOOSAN HP375WCU Operation & Maintenance Manual Download Page 1

 

 

   

 

 

 

  

Doosan Infracore Portable Power 
1293 Glenway Drive
Statesville, N.C. 28625
www.doosanportablepower.com

Book: 22592083 (1-07) Rev A 

This manual contains important safety information.

Do not destroy this manual.

This manual must be available to the personnel who operate and maintain this machine.

 

OPERATION, MAINTENANCE 

COMPRESSOR MODELS

P425WCU 

      MANUAL

XP375WCU
HP375WCU

Doosan purchased Bobcat Company from Ingersoll-Rand Company in
2007. Any reference to Ingersoll-Rand Company or use of trademarks,
service marks, logos, or other proprietary identifying marks belonging
to Ingersoll-Rand Company in this manual is historical or nominative
in nature, and is not meant to suggest a current affiliation between
Ingersoll-Rand Company and

 Doosan

 Company

 

or the

 

products

 

of

either.

Revised (

10

-12)

Summary of Contents for DOOSAN HP375WCU










































































Reviews:

No comments