16573339_ed2
5
8.
For Models 77H90H84, 77H90H84-EU, 77H120H84 and
77H120H84-EU,
install a Wheel Flange (44), Wheel and the
other Wheel Flange (44) onto the Arbor (35) so that the keys are
opposite each other.
For Models 77H120H63, 77H120H63-EU, 77H150H63 and
77H150H63-EU,
install a Wheel Flange (53) so the pin in the
Arbor (36) enters the hole in the side of the flange. Install the
Wheel and the other Wheel Flange (53).
9. Using an applicable spanner wrench inserted into the pin
hole of the inboard flange to hold the arbor, install the Wheel
Nut (46 or 54) with an open-end wrench. Only tighten sufficiently
to drive the wheel and prevent slippage. Remove the Arbor
Housing from the vise.
10.
For Models 77H90L10, 77H90L10-EU, 77H120L10 and
77H120L10-EU,
install the Wheel Bearing Cap (60), Dust
Washer (60B) and Cap Spring (60A) on the Arbor (37). Press the
Wheel End Bearing (59) on the end of the Arbor.
11. Grasp the Arbor (37) in a vise, spline end up.
12. Install the Bearing Lock Washer (58) and Bearing Locknut (57)
onto the Arbor (37). Tighten the Locknut snugly. Bend the tangs
of the Bearing Lock Washer into the grooves of the Bearing
Locknut.
13. Remove the Arbor from the vise.
14. Grasp the Arbor Housing (22) in a vise, threaded end up.
15. Lubricate with 3 to 4 cc of
Ingersoll Rand
No. 68 Grease and
install the Arbor Coupling (34) into the Arbor Housing and onto
the spline of the rotor shaft.
16. Slide the spline of the Arbor (37) into the Arbor Coupling. Tighten
the Wheel Bearing Cap to 25 to 30 ft-lb (34 to 41 Nm) torque.
17. Using a No. 74RAQT4-254 Cone Wheel Arbor Wrench to hold
the Arbor (37), install the cone wheel turning clockwise until
hand-tight. Remove the Arbor Housing from the vise.
18.
For Model 77H90G6,
press the Wheel End Bearing (63) onto the
Arbor (38).
19. Grasp the Arbor (38) in a vise, spline end up.
20. Install the Bearing Lock Washer (62) and Bearing Locknut (61)
onto the Arbor (38). Tighten the Locknut snugly. Bend the tangs
of the Bearing Lock Washer into the grooves of the Bearing
Locknut.
21. Remove the Arbor from the vise.
22. Grasp the Arbor Housing (22) in a vise, threaded end up.
23. Lubricate with 3 to 4 cc of
Ingersoll Rand
No. 68 Grease and
install the Arbor Coupling (34) into the Arbor Housing and onto
the spline of the rotor shaft. Slide the spline of the Arbor (38) into
the Arbor Coupling (34).
24. Install the Wheel Bearing Cap (64), Cap Spring (64A) and Dust
Washer (64B). Tighten the Cap to 25 to 30 ft-lb (34 to 41 Nm)
torque.
25. Install the Collet (66) into the end of the Arbor.
26. Use a No. DG120-69 Collet Arbor Wrench to hold the Arbor. Use
a No. DG120-69 Collet Nut Wrench to tighten the Collet Nut (65).
Remove the Arbor Housing from the vise.
27.
For Models 77H30B106, 77H30B106-EU, 77H50B106 and
77H50B106-EU,
press the Wheel End Bearing (73) into the Arbor
Housing (22) and onto the Arbor (39).
28. Grasp the Arbor Housing (22) in a vise, threaded end up.
29. Install the Wheel Bearing Cap (74), Cap Spring (74A) and Dust
Washer (74B). Tighten the Cap to 25 to 30 ft-lb (34 to 41 Nm)
torque.
30. Install the Wheel End Bearing Nut and tighten snugly.
31. Install the Wire Brush Long Spacer (77), Wire Brush Short
Spacer (77A), Wire Brush, Wire Brush Short Spacer (77A), Wire
Brush Lock Washer (76) and Wire Brush Nut (78). Use a wrench
on the flats of the Wheel End Bearing Nut (75) to hold the Arbor.
Using an open-end wrench, tighten the Wire Brush Nut (78)
securely. Remove the Arbor Housing from the vise.
Summary of Contents for 77H Series
Page 7: ...Notes...
