Ingenico iCT2XX Operating Manual Download Page 65

Page: 65 / 147

SKYZER TECHNOLOGIES

PAGE 65 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

8.1.2

GPRS Configuration

Step

Terminal Display

Comment

1.0

Press

FUNC

2.0

FUNCTION?

Enter

2467

and press

ENTER.

3.0

TMS CONFIG
ENTER OR CLEAR

Press

ENTER

to configure the TMS parameters,

CLEAR

to cancel and exit to idle

prompt.

4.0

TMS TERMINAL ID?
XXXXXXXX

This parameter specifies the TMS Terminal ID which is by default the last 8 digits of
the terminal serial number.

6.0

TMS NII
201

This parameter specifies the Network International Identifier that the terminal uses
to route messages to TMS.

Press

ENTER.

7.0

TMS URL
www.skyzertms.co.n
z

This parameter specifies the TMS URL. By default is set to

www.skyzertms.co.nz

Press

ENTER.

8.0

PRIMARY

HOST IP ADDRESS
202.180.114.12

This parameter specifies the Primary Host IP Address. By default is set to

202.180.114.12

Press

ENTER.

9.0

PRIMARY

HOST PORT

3200

This parameter specifies the Primary Host Port number. By default is set to

3200.

Press

ENTER.

9.0

APN?
paymarkfreedom.co.
nz

This parameter specifies the Access Point Name of the Paymark network or any
third party SIM card which has been configured for.

10.0

SAVE CONFIG Y/N

Press

ENTER

to save the configuration or

CLEAR

to exit without saving

configuration.

Summary of Contents for iCT2XX




















































































































































Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands

Ingenico iCT2XX, Operating Manual

Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands