Ingenico iCT2XX Operating Manual Download Page 45

Page: 45 / 147

SKYZER TECHNOLOGIES

PAGE 45 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

5.3 Multi-Merchant Configuration

This function is used to configure the terminal for Multi-merchant operation. The
terminal can support up to 8 Merchants.

NOTE:

After activating the Multi-Merchant configuration, please return to

EFTPOS configuration for Multi-Merchant

Function

3824

to enter the Terminal

d Merchant ID’s for the active merchants.

Step

Terminal Display

Description

1.0

Press

FUNC

2.0

FUNCTION?

Enter

7418

, press

ENTER

3.0

MULTI MERCHANT

SETUP

Terminal is now in configuration mode. Go to following steps to proceed or press

CANCEL

to exit, otherwise the terminal will automatically exit after 30 seconds of

inactivity

Summary of Contents for iCT2XX




















































































































































Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands

Ingenico iCT2XX, Operating Manual

Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands