Lane/8000
900028753 R11 000 01/1216
Lane/8000
900028753 R11 000 01/1216
Copyright© 2016 Ingenico
All rights reserved
Copyright© 2016 Ingenico
All rights reserved
2_
Security of your terminal
Your device fulfi ls current applicable PCI PTS security requirements.
Upon receipt of your terminal you should check for signs of tampering of the equipment. It is strongly advised that these checks
are performed regularly after receipt. You should check, for example: that the keypad is fi rmly in place; that there is no evidence of
unusual wires that have been connected to any ports on your terminal or associated equipment, the chip card reader or any other
part of your terminal. Such checks would provide warning of any unauthorised modifi cations to your terminal, and other suspicious
behaviour of individuals that have access to your terminal. Your terminal detects any “tampered state”. In this state the terminal will
repeatedly fl ash the message” Alert Irruption!” and further use of the terminal will not be possible. If you observe the “Alert Irruption!”
message, you should contact the terminal helpdesk immediately.
You are strongly advised to ensure that privileged access to your terminal is only granted to staff that have been independently
verifi ed as being trustworthy. The terminal must never be put in or left at a location where it could be stolen or replaced by another
device.
CAUTION
Positioning of the Lane/8000 on check stand must be in such a way to make cardholder PIN (Personal Identifi cation
Number) spying infeasible.
Installing device on an adjustable stand must be in such a way that consumers can swivel the terminal sideways and/or
tilt it forwards/backwards to a position that makes visual observation of the PIN-entry process diffi cult.
Positioning of in-store security cameras such that the PIN-entry keypad is not visible.
NEVER ask the customer to divulge their PIN Code. Customers should be advised to ensure that they are not being
overlooked when entering their PIN Code.
2_1
WARNING TO USERS IN THE UNITED STATES
Federal Communication Commission Interference Statement 47 CFR Section 15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures :
Carefully inspect the shipping carton and its contents for shipping damage. If the device is damaged, fi le a claim immediately with the
shipping company and notify Ingenico.
You should have :
Lane / 8000 device
This guide
Save the carton and packing material for repackaging or moving
the device in the future.
The box may also include the following items depending on your
confi guration working :
Power supply unit and Power cord
A stylus
The Lane/8000 magnetic stripe
reader reads debit, credit, and all
standard magnetic stripe cards.
Slide the card from the rear to the
front in a continuous motion for best
results.
Take care to ensure that the
card is inserted in the correct
manner, chip facing up.
Bring the card fi rmly up to the
active area above the display
(at about 1cm). Keep the card
close to the Reader during the
transaction.
On the back side of the terminal,
there is single connector. Connect
only validated cable. Ensure the
other end provide power and host
communication if required. If needed
connect the power supply to the
mains by the wall receptacle.
1_
Equipment check list
1_1
Power & Cable connections
1_2
Magnetic Stripe Reader
1_3
Smart Card Reader
1_4
Contacless Reader
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
2_3
ANTENNA REQUIREMENT
Federal Communication Commission Interference Statement 47 CFR Section 15.203
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
2_4
WARNING TO USERS IN THE CANADA
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions
Connection of headset on audio output jack:
An excessive acoustic pressure of headset can involve deafness!
Only use the power supply AC/DC provided with Lane/8000 (8VDC 2A or 8VDC 3A) or the power provided by a cash
register (16 Watt min, 8V min) limited power source (LPS) or (10W, 5V).
Remove the power jack to power off the terminal.
Authorized power supply units :
PHIHONG TECHNOLOGY Co. Ltd
PSM24W-080L6IN-R
3_
Troubleshooting
3_1
Magnetic Card Reader Does Not Work Properly
1
When sliding the card through the reader, make sure that the magnetic stripe on the card is facing the Lane/8000
display screen (see Magnetic Stripe Reader).
Swipe the card at a faster or middle steady speed.
2
Inspect the magnetic stripe on the card to make sure it is not scratched or badly worn.
3
CAUTION
This equipment may not be modifi ed, altered, or changed in any way without signed written permission from Ingenico.
Unauthorized modifi cation may void the equipment authorization from the FCC and will void the Ingenico warranty.
Consult the dealer or an experienced radio/TV technician for help.
2_2
NO AUNAUTHORIZED MODIFICATIONS
Federal Communication Commission interference Statement 47 CFR Section 15.21
2_5
SAFETY
Security tag deactivation system could disturb the magnetic card reader
4
If your host device has a magnetic stripe reader, try swiping the card there.
If you have another working Lane/8000 device, try swiping the card there.
To determine if the problem is with the card:
5
3_2
Device is not working
Make sure that the Lane/8000 connector is fully inserted into the back of the device.
1
Restart the device.
2
If you have another working Lane/8000 device, swap the devices to determine if the problem is with the device,
cable, POS, or power supply.
3
If the Lane/8000 device is directly connected to a host, reset the host by turning it off and back on again.
4