manualshive.com logo in svg

Ingecon SUN 125 TL U 208 Outdoor, Installation Manual, Page: 69 / 88

Share
Download
Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 69

ABB2000IKI01

69

Installation manual

Ingeteam

MP VIN

High input voltage from the panels.

MP FRED

Incorrect grid frequency.

MP VRED

Incorrect grid voltage.

MP VARISTORES

Varistor fault.

MP AISL.DC

DC insulation fault.

MP INT AC RMS

Continuous overvoltage on AC output.

MP TEMPERATURA

Overtemperature in the power electronics.

MP CONFIG

Shutdown for configuration change.

MP PARO MANUAL

Manual shutdown.

MP B VPV MED

Low input voltage from the panels.

MP HW_DESCX2

Internal fault.

MP IAC INST

Voltage surge on AC output.

MP CR. FIRMWARE

Shutdown due to firmware change.

MP LEC ADC

AD converter (internal) reading fault.

MP CONSUMO POT

Insufficient solar radiation. Does not trigger alarm.

MP FUSIBLE DC

Input fuse fault.

MP TEMP AUX

Redundant temperature sensor fault.

MP PROTECCION AC

AC Protection.

MP MAGNETO AC

Thermomagnetic circuit breaker error.

MP CONTACTOR

Contactor failed to close.

MP RESET_WD

Stopped for Watch Dog reset (internal).

MP LAT ADC

Converter (internal) fault.

MP ERROR FATAL

Fatal error in the inverter.

MP FALLO RAMA1

Power electronics fault.

MP FALLO RAMA2

Power electronics fault.

MP FALLO RAMA3

Power electronics fault.

MP PI CORR SAT

PI current saturation (internal).

MP LATENCIA SPI

Communication fault with redundant system.

MP REDUNDANTE

The redundant system has caused a shutdown.

MP PROTECCIÓN PIB

The PIB has caused a shutdown.

8.6.  Settings

Date and Time

From this menu you can change the date and time. The internal clock automatically changes the time from summer 
to winter and vice versa.

Inverter number change

From this menu you can assign the node number to the inverter. This is required for configuring communications.

Language

With this option, you can select the display language.

In the main screen, press the “down” key (an arrow pointing downwards). Main menu access.

From the main menu, by pressing the 

 or 

 keys or navigating through the menu to “SETTINGS”. Once high-

lighted, press 

 to access the submenu.

Within the “SETTINGS” submenu with the 

 or 

 keys or navigating through the menu to the “Language” 

option. Once highlighted, press 

 to access the language change screen.

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Reviews:

No comments