Infortrend EonStor CS Maintenance Manual Download Page 42

Page: 42 / 133

EonStor CS Installation Guide

page 42 / 133

Installation Guide

1-7 Individual disk pool checking

Go to EonOne’s

Settings > Storage > Disk Pool

to check the cluster Disk Pool status

Disk Pool Status

Status

Description

Good

The disk pool works normally.

Degraded

CS might find issue on member drive or Node, under this situation the local

folder and shared folder is still accessible. But need to check which member

drive or node encountered issue and perform repair or replace to recover it as

soon as possible

Error

There is not only a single drive or node encountered issue, and the failure

number has exceeded the failure tolerance of CS system which cause the data

to become incomplete.

Summary of Contents for EonStor CS






































































































































Search results

Summary of Contents for EonStor CS

Reviews:

Related manuals for EonStor CS

Brands by name

Popular brands

Infortrend EonStor CS, Maintenance Manual

Search results

Summary of Contents for EonStor CS

Reviews:

Related manuals for EonStor CS

Brands by name

Popular brands