INFODRAW PMRS-104 Fast Installation Download Page 4

Chapter 2 -   Unit Hardware Interfaces

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The unit has a standard HDMI which supports 
the video input and audio. 

 

The GPS antenna has a SMA interface located 
on the top of the PMRS unit.  

Connect the GPS antenna to the SMA 
connector

.  

 

The SIM card slot is located on the side of the 
unit. Pull the notch out to insert the SIM card.

 

 

The PMRS has a built in alarm button located 
on the side of the unit. The button can be used 
in emergencies and can be set up to trigger a 
variety of actions on the MRS monitor (Refer to 
Alarm Button Section). 

 

2-1

   

Video Input/ Audio Input/ 5V Power Output: 

2-2

   

GPS Antenna Connector:

 

 

2-4

   

SIM Card Slot:

 

2-5

   

Alarm Button:

 

The PMRS has an internal GSM antenna. 
However an external GSM antenna connector 
can be added to the PMRS if required and has a 
SMA interface which will be located on the top 
corner of the PMRS unit next to the GPS 
antenna.  

 

 

2-3

   

GSM Antenna Connector:

 

 

GPS 

 

GSM 

Summary of Contents for PMRS-104













Reviews: