manualshive.com logo in svg

INFODRAW MRS-400, User Manual, Page: 131 / 194

Share
Download
INFODRAW MRS-400 User Manual Download Page 131

July 14, 2013 

INFODRAW                                        MRS-400 User Manual v5.4.1                                                                        

 

 

 

131 

 

4-3-11  PTZ Menu

: 

 

 

 

 

 

 

 

 

 

 

 

 

 

PTZ Parameters: 

Descriptions: 

Add 

Here you can setup the PTZ control of the MRS-400 unit. 
Press the 

“Add”

 button to add the “Video Channel” and 

“Camera ID”. As the MRS-400 unit only has one video 
channel, set the “Video Channel” and “Camera ID” both to 

1

. 

Baud Rate 

This list box allows you to set the PTZ control Baud Rate. The 
unit supports the following Baud Rates: 
1200/ 1800/ 2400/ 4800/ 9600/ 19200/ 38400/ 57600/ 
115200/ 230400 
The Baud Rate must be set the same for the MRS-400 unit 
and for the PTZ Camera.  

 

For more information, please view the “

PTZ

” section of this 

user manual. 

 

 

 

 

 

Summary of Contents for MRS-400



































































































































































































Reviews:

No comments