INFODRAW MRS-400 User Manual Download Page 125

Page: 125 / 194

July 14, 2013

INFODRAW MRS-400 User Manual v5.4.1

125

4-3-8 GPIO Menu

GPIO Parameters:

Descriptions:

Port Selection

Here you can change the settings of the Input Sensors that
are connected to your device. The Input ports are at

TTL

level

. Start by selecting one of the ports.

Port Name

Here you can change the name of the input sensor to any
desired name.

Not Active

This option will disable the selected port.

Normally Close

This option changes the selected input port to

Active High

Normally Open

This option changes the selected input port to

Active Low

Associated Camera

This option allows you to add or remove the camera for the
selected port.

Associated Microphone

This option allows you to add or remove the microphone
for the selected port.

Record Video

Enable this option to record video on a Micro SD card inside
the device, once a GPIO alarm is triggered.

Record Audio

Enable this option to record audio on a Micro SD card inside
the device, once a GPIO alarm is triggered.

Summary of Contents for MRS-400



































































































































































































Search results

Summary of Contents for MRS-400

Reviews:

INFODRAW MRS-400, User Manual, Page: 125 / 194

Search results

Summary of Contents for MRS-400

Reviews: