MOUNTING THE CROSSOVER
Open the crossover housing by placing your
fingers between the terminals and the top cover,
and gently pulling off the cover. Using screws or
a wire tie, mount the crossover through the holes
provided.
CONNECTIONS
Observing proper polarity, connect the speakers
and amplifier as shown in 8A and 8B. Replace the
cover when you are finished making connections.
Figure 8A.
Wiring connections on the crossover
network (shown with cover on).
Figure 8B.
Locating wiring connections on the
woofer.
TWEETER LEVEL ADJUSTMENT
Located on the right side of the crossover network
is a small switch which controls the tweeter level.
The upper position is +3dB and the lower position
is 0dB. Adjust to personal preference.
Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA
516.674.4463 • FAX 516.682.3523 • www.infinitysystems.com
© 2005 Harman International Industries, Incorporated • Part No. KAPCSOM2/05
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau-du-Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Klaus Lebherz
Harman Consumer Group International
Chateau-du-Loir, France 2/05
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Intermount III patent no. 6,505,705.
50.7cs
Type:
5-1⁄4" 2-Way Component
Crossover Frequency:
3.5kHz
Woofer
Speaker Impedance:
2 ohms
Power Handling:
85W RMS, 255W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
55Hz – 25kHz
Mounting Depth:
2-1/16" (53mm)
Cutout Diameter:
4-11/16" (120mm)
Tweeter
Speaker Impedance:
2 ohms
Power Handling:
50W RMS, 150W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
3.5kHz – 25kHz
Mounting Depth:
3/4" (19mm)
Cutout Diameter:
1-7/8" (48mm)
60.7cs
Type:
6-1⁄2" 2-Way Component
Crossover Frequency:
3.5kHz
Woofer
Speaker Impedance:
2 ohms
Power Handling:
90W RMS, 270W Peak
Sensitivity:
95dB @ 2.83V, 1m
Frequency Response:
45Hz – 25kHz
Mounting Depth:
2-3⁄ 16" (56mm)
Cutout Diameter:
5" (127mm)
Tweeter
Speaker Impedance:
2 ohms
Power Handling:
50W RMS, 150W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
3.5kHz – 25kHz
Mounting Depth:
3/4" (19mm)
Cutout Diameter:
1-7/8" (48mm)
65.7cs
Type:
165mm 2-Way Component
Crossover Frequency:
3.5kHz
Woofer
Speaker Impedance:
2 ohms
Power Handling:
90W RMS, 270W Peak
Sensitivity:
95dB @ 2.83V, 1m
Frequency Response:
45Hz – 25kHz
Mounting Depth:
2-1/4" (58mm)
Cutout Diameter:
5-5/8" (143mm)
Tweeter
Speaker Impedance:
2 ohms
Power Handling:
50W RMS, 150W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
3.5kHz – 25kHz
Mounting Depth:
3/4" (19mm)
Cutout Diameter:
1-7/8" (48mm)
680.7cs
Type:
6" x 8"/5" x 7"
2-Way Component
Crossover Frequency:
3.5kHz
Woofer
Speaker Impedance:
2 ohms
Power Handling:
90W RMS, 270W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
40Hz – 25kHz
Mounting Depth:
2-1/4" (58mm)
Cutout Diameter:
7-1/8" x 4-7/8"
(181mm x 124mm)
Tweeter
Speaker Impedance:
2 ohms
Power Handling:
50W RMS, 150W Peak
Sensitivity:
94dB @ 2.83V, 1m
Frequency Response:
3.5kHz – 25kHz
Mounting Depth:
3/4" (19mm)
Cutout Diameter:
1-7/8" (48mm)
S
PECIFICATIONS
Big Lug =
Small Lug =
TO AMPLIFIER
SPEAKER OUTPUTS
TO WOOFER
TO TWEETER
RED
BLK
I
NSTALLATION
