background image

114

Infinisource

You can now exit the clock menu by pressing <CLR> repeatedly until 
you are brought back to the displayed time.

Initiating a Manual Upload

The stored data in the clock can be manually uploaded to the TimeForce 
database from the clock main menu.

1.

At the clock keypad, press the <MENU> button.

2.

Press 5 for “UPLOAD DATA.”

The clock initiates communication and uploads its stored data.

Uploading the Date and Time

The date and time can be uploaded to the clock from the ClockLink util-
ity. Before you will be able to upload the date and time, you must first 
create a time clock profile in TimeForce for each clock that you would 
like to connect to.

1.

Open the ClockLink utility. From the Windows Start Menu go to 
Programs | TimeForce II and click on “ClockLink.”

2.

Each time clock that has been set up in the TimeForce software is 
listed in the left-hand section of the screen. Highlight the clock that 
you would like to upload the date and time to and click on the 
“Connect” link.

3.

Once communication has been established with your time clock, 
the right-hand section of the screen opens. From the row of tabs at 
the top of the screen, ensure that [PARAMETERS] is selected.

4.

From the 

Actions

 section of the screen, click on the 

 icon. 

The “Upload Date/Time” screen opens.

Enter the desired 

Date

. By default this field is populated with 

the system date of the machine that ClockLink is installed on. 
Click on the down-arrow icon at the end of the field to select 
the date from a calendar. Select the 

Use System Time

 option to 

restore the system date/time.

Summary of Contents for ETC 100











































































































































































































































Reviews: