manualshive.com logo in svg

Infineon XC886CLM, User Manual

The Infineon XC886CLM is a powerful microcontroller with exceptional performance and reliability. Users can easily understand its features and functionalities by downloading the free user manual from manualshive.com. This manual provides detailed instructions on how to maximize the potential of this advanced product.

Share
Download
background image

XC886/888CLM

Capture/Compare Unit 6

 

User’s Manual

14-90

V1.3, 2010-02

CCU6, V 1.0

 

ENWHE

5

rw

Enable Interrupt for Wrong Hall Event

0

No interrupt will be generated if the set condition 
for bit WHE in register IS occurs.

1

An interrupt will be generated if the set condition 
for bit WHE in register IS occurs. The interrupt 
line that will be activated is selected by bit field 
INPERR.

ENIDLE

6

rw

Enable Idle

This bit enables the automatic entering of the idle state 
(bit IDLE will be set) after a wrong hall event has been 
detected (bit WHE is set). During the idle state, the bit 
field MCMP is automatically cleared.
0

The bit IDLE is not automatically set when a 
wrong hall event is detected.

1

The bit IDLE is automatically set when a wrong 
hall event is detected.

ENSTR

7

rw

Enable Multi-Channel Mode Shadow Transfer 
Interrupt

0

No interrupt will be generated if the set condition 
for bit STR in register IS occurs.

1

An interrupt will be generated if the set condition 
for bit STR in register IS occurs. The interrupt 
line that will be activated is selected by bit field 
INPCHE.

0

3

r

Reserved

Returns 0 if read; should be written with 0.

INPL
Capture/Compare Interrupt Node Pointer Register Low      

Reset Value: 40

H

7

6

5

4

3

2

1

0

INP

CHE

INP

CC62

INP

CC61

INP

CC60

rw

rw

rw

rw

Field

Bits

Type Description

*

Summary of Contents for XC886CLM
























































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XC886CLM

GE PACSystems* RX3i Application Manual preview
PACSystems* RX3i
Brand: GE Pages: 39
GE PACSystems* RX3i Secure Deployment Manual preview
PACSystems* RX3i
Brand: GE Pages: 35
GE PACSystems* RX3i Important Product Information preview
PACSystems* RX3i
Brand: GE Pages: 3
GE PACSystems* RX3i User Manual preview
PACSystems* RX3i
Brand: GE Pages: 169
E-T-A EtherNetIP ControlPlex CPC12EN User Manual preview
EtherNetIP ControlPlex CPC12EN
Brand: E-T-A Pages: 28
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Brand: u-blox Pages: 2
Bartlett 3K Operation Manual preview
3K
Brand: Bartlett Pages: 7
Xilinx ZC702 Getting Started Manual preview
ZC702
Brand: Xilinx Pages: 52
Airlow CP Touch User Manual preview
CP Touch
Brand: Airlow Pages: 20
Morningstar SUNSAVER SS-10-12V Installation And Operation Manual preview
SUNSAVER SS-10-12V
Brand: Morningstar Pages: 26
NovaStar NovaPro UHD Manual preview
NovaPro UHD
Brand: NovaStar Pages: 11
Halma Alicat Scientific MC Quick Start Manual preview
Alicat Scientific MC
Brand: Halma Pages: 2
TDSi DIGIgarde PLUS User Manual preview
DIGIgarde PLUS
Brand: TDSi Pages: 71
Azbil AUR455 User Manual preview
AUR455
Brand: Azbil Pages: 68
Ltech LT-3900IR Manual preview
LT-3900IR
Brand: Ltech Pages: 2
OBO Bettermann C50-0-255 Installation Instructions Manual preview
C50-0-255
Brand: OBO Bettermann Pages: 6
Zareba LIS10 User Manual preview
LIS10
Brand: Zareba Pages: 40

Brands by name

Popular brands

Load more brands