Infineon TLD5098EP User Manual Download Page 14

Trademarks
All referenced product or service names and trademarks are the property of their respective owners.

Edition 2020-09-17
Published by
Infineon Technologies AG
81726 Munich, Germany
 

©

 2020 Infineon Technologies AG

All Rights Reserved.
 
Do you have a question about any

aspect of this document?
Email: 

[email protected]

 
Document reference

IFX-lfi1595842022571

IMPORTANT NOTICE
The  information  contained  in  this  application  note  is

given  as  a  hint  for  the  implementation  of  the  product

only and shall in no event be regarded as a description

or  warranty  of  a  certain  functionality,  condition

or  quality  of  the  product.  Before  implementation

of  the  product,  the  recipient  of  this  application

note  must  verify  any  function  and  other  technical

information  given  herein  in  the  real  application.

Infineon  Technologies  hereby  disclaims  any  and  all

warranties and liabilities of any kind (including without

limitation warranties of non-infringement of intellectual

property  rights  of  any  third  party)  with  respect  to  any

and all information given in this application note.
The  data  contained  in  this  document  is  exclusively

intended  for  technically  trained  staff.  It  is  the

responsibility  of  customer’s  technical  departments  to

evaluate the suitability of the product for the intended

application  and  the  completeness  of  the  product

information given in this document with respect to such

application.

WARNINGS
Due to technical requirements products may contain

dangerous substances. For information on the types

in  question  please  contact  your  nearest  Infineon

Technologies office.
Except as otherwise explicitly approved by Infineon

Technologies  in  a  written  document  signed  by

authorized representatives of Infineon Technologies,

Infineon Technologies’ products may not be used in

any  applications  where  a  failure  of  the  product  or

any consequences of the use thereof can reasonably

be expected to result in personal injury.

Summary of Contents for TLD5098EP















Reviews: