Infineon Cypress S29GL01GS, Manual

Page: 73 / 109

Document Number: 001-98285 Rev. *R Page 72 of 108
S29GL01GS/S29GL512S
S29GL256S/S29GL128S
10.5 DC Characteristics
Notes:
1. I
CC
active while Embedded Algorithm is in progress.
2. Not 100% tested.
3. Automatic sleep mode enables the lower power mode when addresses remain stable for the specified designated time.
4. V
IO
= 1.65V to V
CC
or 2.7V to V
CC
depending on the model.
5. V
CC
= 3V and V
IO
= 3V or 1.8V. When V
IO
is at 1.8V, I/O pins cannot operate at >1.8V.
6. During power-up there are spikes of current demand, the system needs to be able to supply this current to insure the part initializes correctly.
7. If an embedded operation is in progress at the start of reset, the current consumption will remain at the embedded operation specification until the embedded operation
is stopped by the reset. If no embedded operation is in progress when reset is started, or following the stopping of an embedded operation, I
CC5
will be drawn during
the remainder of t
RPH
. After the end of t
RPH
the device will go to standby mode until the next read or write.
8. The recommended pull-up resistor for RY/BY# output is 5k to 10k Ohms.
Table 10.4 DC Characteristics (–40 °C to +85 °C)
Parameter Description Test Conditions Min
Typ
(Note 2)
Max Unit
I
LI
Input Load Current V
IN
= V
SS
to V
CC
, V
CC
= V
CC
max – +0.02 ±1.0 µA
I
LO
Output Leakage Current V
OUT
= V
SS
to V
CC
, V
CC
= V
CC
max – +0.02 ±1.0 µA
I
CC1
V
CC
Active Read Current
CE# = V
IL
, OE# = V
IH
, Address
switching @ 5 MHz, V
CC
= V
CC
max
– 55 60 mA
I
CC2
V
CC
Intra-Page Read Current
CE# = V
IL
, OE# = V
IH
, Address
switching @ 33 MHz, V
CC
= V
CC
max
– 9 25 mA
I
CC3
V
CC
Active Erase/Program
Current (Notes 1 , 2 )
CE# = V
IL
, OE# = V
IH
, V
CC
= V
CC
max – 45 100 mA
I
CC4
V
CC
Standby Current
CE#, RESET#, OE# = V
IH
, V
IH
= V
IO
V
IL
= V
SS
, V
CC
= V
CC
max
– 70 100 µA
I
CC5
V
CC
Reset Current (Notes 2 , 7 )
CE# = V
IH
, RESET# = V
IL
,
V
CC
= V
CC
max
– 10 20 mA
I
CC6
Automatic Sleep Mode (Note 3)
V
IH
= V
IO
, V
IL
= V
SS
,
V
CC
= V
CC
max, t
ACC
+ 30 ns
– 3 6 mA
V
IH
= V
IO
, V
IL
= V
SS
,
V
CC
= V
CC
max, t
ASSB
– 100 150 µA
I
CC7
V
CC
Current during power up
(Notes 2 , 6 )
RESET# = V
IO,
CE# = V
IO
, OE# = V
IO
,
V
CC
= V
CC
max,
– 53 80 mA
V
IL
Input Low Voltage (Note 4) –0.5 – 0.3 × V
IO
V
V
IH
Input High Voltage (Note 4) 0.7 × V
IO
– V
IO
+ 0.4 V
V
OL
Output Low Voltage (Notes 4 , 8 )
I
OL
= 100 µA for DQ15–DQ0;
I
OL
= 2 mA for RY/BY#
– – 0.15 × V
IO
V
V
OH
Output High Voltage (Note 4) I
OH
= 100 µA 0.85 × V
IO
– – V
V
LKO
Low V
CC
Lock-Out Voltage
(Note 2)
2.25 – 2.5 V
V
RST
Low V
CC
Power on Reset
Voltage (Note 2)
– 1.0 – V