manualshive.com logo in svg

Infineon Cypress BCM43353, Manual

Share
Download
Infineon Cypress BCM43353 Manual Download Page 42

Document Number: 002-14949 Rev. *G

Page 41 of 113

PRELIMINARY

CYW43353

9.  WLAN Host Interfaces

9.1 SDIO v3.0

The CYW43353 WLAN section supports SDIO version 3.0, including the new UHS-I modes:

■

DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3V signaling). 

■

HS: High speed up to 50 MHz (3.3V signaling).

■

SDR12: SDR up to 25 MHz (1.8V signaling). 

■

SDR25: SDR up to 50 MHz (1.8V signaling). 

■

SDR50: SDR up to 100 MHz (1.8V signaling). 

■

SDR104: SDR up to 208 MHz (1.8V signaling).

■

DDR50: DDR up to 50 MHz (1.8V signaling). 

Note: 

The CYW43353 is backward compatible with SDIO v2.0 host interfaces.

The SDIO interface also has the ability to map the interrupt signal on to a GPIO pin for applications requiring an interrupt different
from the one provided by the SDIO interface. The ability to force control of the gated clocks from within the device is also provided.
SDIO mode is enabled by strapping options. Refer to 

Table 16

 WLAN GPIO Functions and Strapping Options. 

The following three functions are supported:

■

Function 0 Standard SDIO function (Max. BlockSize/ByteCount = 32B)

■

Function 1 Backplane Function to access the internal system-on-chip (SoC) address space 

(Max. BlockSize/ByteCount = 64B)

■

Function 2 WLAN Function for efficient WLAN packet transfer through DMA 

(Max. BlockSize/ByteCount = 512B)

9.1.1  SDIO Pins

Table 12. SDIO Pin Description

Figure 17. Signal Connections to SDIO Host (SD 4-Bit Mode) 

SD 4-Bit Mode

SD 1-Bit Mode

gSPI Mode

DATA0

Data line 0

DATA

Data line

DO

Data output

DATA1

Data line 1 or Interrupt 

IRQ

Interrupt

IRQ

Interrupt

DATA2

Data line 2 or Read Wait 

RW

Read Wait

NC

Not used

DATA3

Data line 3

N/C

Not used

CS

Card select

CLK

Clock

CLK

Clock

SCLK

Clock

CMD

Command line

CMD

Command line

DI

Data input

 

SD Host

CYW43353

CLK

CMD

DAT[3:0]

Summary of Contents for Cypress BCM43353



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands