manualshive.com logo in svg

Infineon Technologies XC2200, User Manual

Share
Download
Infineon Technologies XC2200 User Manual Download Page 218

XC2200 Derivatives

System Units (Vol. 1 of 2)

Interrupt and Trap Functions

 

User’s Manual

5-6

V2.1, 2008-08

ICU_X2K, V2.2

 

Both the OCDS break requests and the hardware traps bypass the arbitration scheme
and go directly to the core (see also 

Figure 5-2

).

The arbitration process starts with an enabled interrupt request and stays active as long
as an interrupt request is pending. If no interrupt request is pending the arbitration is
stopped to save power.

Interrupt Control Registers

The control functions for each interrupt node are grouped in a dedicated interrupt control
register (xxIC, where “xx” stands for a mnemonic for the respective node). All interrupt
control registers are organized identically. The lower 9 bits of an interrupt control register
contain the complete interrupt control and status information of the associated source
required during one round of prioritization (arbitration cycle); the upper 7 bits are
reserved for future use. All interrupt control registers are bit-addressable and all bits can
be read or written via software. Therefore, each interrupt source can be programmed or
modified with just one instruction.

xxIC 
Interrupt Control Register

(E)SFR (yyyy

H

/zz

H

)

Reset Value: - 000

H

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

-

-

-

-

-

-

-

GPX xxIR xxIE

ILVL

GLVL

-

-

-

-

-

-

-

rw

rwh

rw

rw

rw

Field

Bits

Type

Description

GPX

8

rw

Group Priority Extension

Completes bitfield GLVL to the 3-bit group level

xxIR

1)

7

rwh

Interrupt Request Flag

0

No request pending

1

This source has raised an interrupt request

xxIE

6

rw

Interrupt Enable Control Bit

(individually enables/disables a specific source)
0

Interrupt request is disabled

1

Interrupt request is enabled

ILVL

[5:2]

rw

Interrupt Priority Level

FH

Highest priority level

…

…

0H

Lowest priority level

Summary of Contents for XC2200






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands