manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 689

TC1796

System Units (Vol. 1 of 2)

Direct Memory Access Controller

 

User’s Manual

12-25

V2.0, 2007-07

DMA, V2.0

 

Figure 12-16 DMA Break Event Generation

12.1.7.4 Trace Signal Generation

The TC1796 provides sixteen OCDS Level 2 debug output lines OCDSL2[15:0]. These
16 output lines can be selected to output trace data of the DMA controller. Two trace data
types are possible:
•

Channel trace for monitoring the transaction request flags CHmn of register
DMA_TRSR

•

Move Engine trace for monitoring the status flags and bit fields of register
DMA_MESR

Channel trace and Move Engine trace outputs are selected by bit TRCDS in the OSCU
Configuration and Control Register OCNTRL. The selected DMA trace is further enabled
to the trace output lines TR[15:0] by bit OCNTRL.TRCDEN.
The information that is output on the TR[15:0] trace port lines is shown in the following
diagram.

TRSR

CH01

BREAK

BCHS0

OCDSR

TRSR

CH07

Edge

Detection

BTCR0

OCDSR

&

BRL0

OCDSR

Enabled
Transaction
Lost Interrupts
00-07

TRSR

CH11

BCHS1

OCDSR

TRSR

CH17

Edge

Detection

BTCR1

OCDSR

Enabled
Transaction
Lost Interrupts
10-17

&

BRL1

OCDSR

DMA Sub-Block 0

DMA Sub-Block 1

MCA05695

3

2

2

3

≥

1

≥

1

≥

1

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands