manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 134

TC1796

System Units (Vol. 1 of 2)

CPU Subsystem

 

User’s Manual

2-37

V2.0, 2007-07

CPU, V2.0

 

The DMI control register 1 is required for data cache test purposes. It is noted here for
the sake of completeness.

DMI_CON1
DMI Control Register 1

(F87FFC28

H

)

Reset Value: 0000 0000

H

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

0

r

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

0

DC2
SPR

r

rw

Field

Bits

Type Description

DC2SPR

0

rw

Cache Test Mode Enable

This bit must always be written with 0.
Setting to 1 will have no effect in TC1796.

0

[31:1]

r

Reserved

Returns 0 when read; should be written with 0.

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands