Inficon Sensistor Sentrac Service Instructions Manual Download Page 65

Page: 65 / 76

INFICON

Software | 6

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

65 / 76

6.3.4 Test Board

Shows I/O connector out and input status. With a test board it is possible to make a

self test (Start button).

6.4 Impact of different Settings

Parameters in Measuring Mode and Locating.

Calculate

Parameter

Unit

Explanation

Processed

sensor signal

Unit less

Output signal from processed sensor

signal

Calibration

factor

Unit less

Diagnosis / Service Screen / Calibration

factor

Internal factor to store calibration

results. (internal factor, not showed)

Conversion

factor

Unit less

Diagnosis / Service Screen / Conversion

factor

Internal calculated relationship

between different unit and gases.

Conversion value is set to 1 when

ppm is selected as calibration unit

and/or measuring Unit.

Measure

value

Unit less

Measuring Mode or

Diagnosis / Service Screen / Signals /

Measuring value

Measuring result

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands