manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Operating Manual

Share
Download
Inficon Sensistor ISH2000 HySpeed Operating Manual Download Page 36

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

36

OM-Sensistor ISH2000-EN-201304

EN

calibration is required to be useful. Contact INFICON AB to have the code sent to 
you. See the web address under section-Info.

Debug Mode

This mode is used during service and software development.

Service Mode

This mode contains useful information to analyze the gas sensor behavior and the 
APC I/O‘s and timers.

8.13   Combined Mode

In 

Combined Mode

 the bar and the sound in 

Locating Mode

 is combined with the 

figures in 

Measuring Mode

.

The loud speaker sound follows the Locating Mode signal.

Note:

After a system reset the default mode is 

Combined Mode

. 

When you have located the leak then you can measure its size in the following way:

1. Remove the probe from the leak.
2. Wait until 0.0 appears on the display
3. Then put the tip of the probe on the leak.

8.14   Probe

The Hand Probe P50 is a non-sniffing probe. Gas Measuring takes place in a sensor 
that is in the tip of the probe. The probe is equipped with a function button, 
indicator lamps, and lighting. The probe can be ordered with a flexible neck.

During operation the heat of the probe tip is 50ºC

Note:

There are a variety of different probes that can be connected to the Sensistor 
ISH2000. When using an active probe please refer to the respective probe 
manual.

Changing the Probe

After attaching a probe the Sensistor ISH2000 needs to stabilize, and the green LED 
should blink. If it does not, then there is a fault in the cable or the hydrogen sensor 
inside the probe is faulty.

When the stabilization period is over the green LED should stay on. Before using the 
Sensistor ISH2000 the instrument needs to be calibrated. Repeat calibration after 
one hour to achieve greatest accuracy.

Changing the Probe Tip

The probe tip (sensor for P50) is replaceable and is locked with a union nut. The 
union nut seals against contact with moisture. If you are not sure about changing 
the probe tip then we recommend that you send it to an authorized service center.

To change the probe tip do the following steps:

1. Turn off the instrument.
2. Loosen the safety nut with a 10 mm wrench.

Summary of Contents for Sensistor ISH2000 HySpeed



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands