manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Operating Manual

Share
Download
Inficon Sensistor ISH2000 HySpeed Operating Manual Download Page 34

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

34

OM-Sensistor ISH2000-EN-201304

EN

* For password to access 

Service Setting

, please contact INFICON.

Audio Base Frequency

This sets the lowest audio base frequency tone in Measuring and Locating Mode. 

Set Clock 

Real time set as hh:mm:ss. Hours and minutes can be adjusted. Seconds will 
automatically be set to 00 when hours and minutes have been set. Clock runs even 
when detector is disconnected from the power supply.

Set Date

Real time clock date set as YY-MM-DD. Clock runs even when detector is 
disconnected from the power supply.

Data Output*

The Sensistor ISH2000 is equipped with a serial (RS232) printer port for data output. 
See “Printer port” on page 39.

* Not in ILS500 Mode

Info

Contains information about software versions, Serial number, and Internet contact 
information.

8.12   Service Settings

Service Settings

 contains important settings that the customer should not change 

without supervisor guidance. To enter 

Service Settings 

menu a password is required. 

Contact your local supplier for help.

Calibration 
(settings)

Yes

Yes

Yes

Yes

Locating Mode 
Settings

Yes

Yes

Measuring Mode 
Settings

Yes

Yes

Yes

Yes

Display Settings

Yes

Yes

General Settings

Yes

Yes

Yes

Yes

Service Settings*

Yes

Yes

Yes

Yes

Yes

Password 
protected 
settings/
functions

Non 
(No password has 
been set)

Standard

Standard
+
Password
Protected
Calibration

High

High
+
Password
Protected
Calibration

Summary of Contents for Sensistor ISH2000 HySpeed



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands