Inficon ELT3000 Translation Of The Original Operating Instructions Download Page 35

Page: 35 / 74

INFICON

Operation | 6

ELT3000-Battery Leak-Detector-Operating-instructions-mina95en1-10-(2007)

35 / 74

6 Operation

WARNING

Risk of injury from flammable solvents

The solvent in the calibration leak is highly flammable.

Overheating can damage the membrane, solvent can leak and ignite from an ignition

source.

► Observe the manufacturer's safety data sheets and follow the applicable work

instructions.

► Avoid heating the calibration leak to high temperatures.

NOTICE

Health risk due to gases and vapors

Operation of the leak detector may produce hazardous vapors.

► Connect the Gas Detection Unit and the Gas Control Unit to an exhaust line.

► Avoid inhaling harmful gases or vapors.

► Ensure sufficient ventilation at the installation location.

► Observe the safety instructions in the safety data sheets for the test objects.

► Provide an installation location where blockage of the exhaust lines is not possible

or can be detected.

► Provide an installation location with adequate ventilation or alternatively an

installation location where air quality is tested and monitored for harmful

substances.

NOTICE

Property damage due to overheated device

The Gas Detection Unit as well as the Gas Control Unit will become warm during

operation and may overheat without adequate ventilation.

► Keep the underside of the gas control unit unobstructed.

► Do not block the ventilation opening for the filter.

► Make sure that there is adequate ventilation at the Gas Detection Unit: Free space

at least 20 cm on the sides, at least 10 cm at the front and rear.

► Keep heat sources away from the battery leak detector.

► Do not expose the battery leak detector to direct sunlight.

► Please note the technical specifications.

Summary of Contents for ELT3000











































































Search results

Summary of Contents for ELT3000

Reviews:

Related manuals for ELT3000

Brands by name

Popular brands

Inficon ELT3000, Translation Of The Original Operating Instructions

Search results

Summary of Contents for ELT3000

Reviews:

Related manuals for ELT3000

Brands by name

Popular brands