Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 8

Page: 8 / 68

2 | Safety

INFICON

8 / 68

Contura® S400-Operating-instructions-jina91en1-09-(2001)

2 Safety

2.1 Duties of the operator

• Read, observe, and follow the information in this manual and in the work

instructions provided by the owner. This concerns in particular the safety and

warning instructions.

• Always observe the complete operating instructions for all work.

• If you have any questions about operation or maintenance that are not answered

in this manual, please contact Customer Service.

2.2 Intended use

The device is a leak detector, in which test objects are tested for leaks in the foil

chamber.

• Operate the device only according to this instruction manual.

• Comply with application limits, see "Technical Data".

Improper use

Avoid the following, non-intended uses:

• Use outside the technical specifications, see "Technical Data"

• Use in radioactive areas

• Close the measuring chamber, while your fingers are in the swing area of the

measuring chamber

• Use of accessories or spare parts, which are not included in this instruction

manual

• Test of test objects that touch the sealing lips of the foil chamber

• Test of test objects, where no gas is enclosed (e.g. vacuum packaging).

• Test of sharp objects

• Test of wet or damp test objects

• Test of test objects that contain liquids.

• Pumping down of condensible fluids and vapors

• Test of test objects with significant differences in temperature to the environment

• Contaminating the measuring chamber or the sealing lips.

• Using the device in potentially explosive atmospheres

Note: This device is not intended to be used in residential areas and cannot ensure

adequate protection of radio reception in such environments.

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands