Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 39

Page: 39 / 68

INFICON

Operation | 6

Contura® S400-Operating-instructions-jina91en1-09-(2001)

39 / 68

> Data backup > Save data

6.8 Restore user and product data

Overwrite current user and product data

By restoring stored user and product data the current state of these data is deleted.

Supervisor - rights

You have a USB flash drive (FAT32 formatted) with user and product data from a

backup.

Insert the USB stick into a USB port on the device.

> Data backup > Restore data

6.9 Restoring factory defaults

You can restore the device to factory settings.

Loss of settings and measurement data

After resetting to factory defaults only the manufacturer factory settings is in the

memory of the device.

Backup important settings and measurement data beforehand on a USB flash drive.

See "Save user and product data [

}

38]" and "Transferring measurement data [

}

35]".

Supervisor - rights

►

> Reset device

6.10 Calibrating the device

6.10.1 Reasons for calibration

In the following cases, calibration is mandatory:

• The installation site of the leak detector is located above 1000 m above sea level.

• The measuring chamber was changed.

• There are operational requirements for a calibration.

6.10.2 Calibration means

There are various calibration means for the device available:

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands