GB
7
Table of burner and nozzle specifications
Table 1
Liquid gas
Natural gas
BURNER
Diameter
(mm)
Thermal Power
kW (p.c.s. *)
By-pass
1/100
(mm)
Nozzle
1/100
Nozzle
1/100
(mm)
Flow *
g/h
Flow *
l/h
(mm)
Nomin.
Red.
G30/31
G20
Fast (Large) (R)
0
100
3.00
0.7
40
86
218
116
286
Semi-Fast (Medium) (S)
5
75
1.65
0.4
30
64
120
96
157
Auxiliary (Small) (A)
55
1.00
0.4
30
50
73
71
95
Triple Crown (TC)
130
3.25
1.3
57
91
236
124
309
Supply pressure
Nominal (mbar)
Minimal (mbar)
Maximised (mbar)
28-30
20
35
20
17
25
*
At 15°C and 1013 mbar - dry gas
Propane G31
P.C.S. = 50.37 MJ/Kg
Butane G30
P.C.S. = 49.47 MJ/Kg
Methane G20 P.C.S. = 37.78 MJ/m
3
Start-up and use
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring showing
the strength of the flame for the relevant burner.
The symbols
near the knobs show the position of the
relative burner on the hob.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an anticlockwise
direction so that it is pointing to the maximum flame setting
.
3. Adjust the intensity of the flame to the desired level by
turning the BURNER knob in an anticlockwise direction.
This may be the minimum setting , the maximum setting
or any position in between the two.
If the appliance is fitted with an
electronic lighting device* (see
figure), press the BURNER knob
and turn it in an anticlockwise
direction, towards the minimum
flame setting, until the burner is lit.
The burner might be extinguished
when the knob is released. If this
occurs, repeat the process, holding
the knob down for a longer period of time.
!
If the flame is accidentally extinguished, switch off the burner
and wait for at least 1 minute before attempting to relight it.
If the appliance is equipped with a flame failure safety device*,
press and hold the BURNER knob for approximately 2-3
seconds to keep the flame alight and to activate the device.
To switch the burner off, turn the knob until it reaches the
stop position
●
.
Practical advice on using the burners
For the burners to work in the most efficient way possible and
to save on the amount of gas consumed, it is recommended
that only pans which have a lid and a flat base are used.
They should also be suited to the size of the burner.
Burner
Fast (R)
Semi Fast (S)
Auxiliary (A)
Triple Crown (TC)
Ø Cookware Diameter (cm)
24 - 26
16 - 22
10 - 14
24 - 26
The hob is fitted with
reducing pan stands
,
which should only be used on auxiliary burner
(A).
For the best performance of your burners, keep the following
in mind: All types of pans can be used on the burners. The
important thing is that the bottom should be completely even.
Using the oven
WARNING !
The oven is
provided with a stop system to
extract the racks and prevent
them from coming out of the
oven (1).
As shown in the drawing, to
extract them completely, simply
lift the racks, holding them on
the front part, and pull (2).
*
Only available in certain models.
