![background image](http://html.mh-extra.com/html/ims/pulsemig-300-t2/pulsemig-300-t2_manual_2049892022.webp)
22
PULSEMIG 300-T2
EN
The manufacturer does not incur any responsability regarding damages to both objects and persons that result from an incorrect
and/or dangerous use of the machine.
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualified person.
• Ensure the machine is switched off by unplugging it, and then wait 2 minutes before carrying out maintenance work. High
Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the electrical connections checked by a qualified
person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be replaced by the manufacturer, its after sales
service or an equally qualified person to prevent danger.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use these machines to unfreeze pipes.
DESCRIPTION
The PULSEMIG is a semi-automatic welding unit; ventilated for semi-automatic welding (MIG or MAG) and can weld
steel, stainless steel and aluminum. Adjustment is quick and easy with its « synergic wire speed » function.
ALIMENTATION ÉLECTRIQUE
The absorbed effective current (I1eff) shown on the machine is when used at maximum output. Check that the power
supply and its protection (fuse and/or circuit-breaker) are compatible with the necessary current during use.
The device must be placed in such way that the power socket is always accessible.
Do not use an extension cord which has a wire section smaller than 1.5 mm².
It must be connected to a 400 V (3PH) supply WITH earth and protected by a circuit breaker (16A and 1 differential
30mA).
It can also be used on a 230V network ( PE), 50/60 Hz, then it will be advised to use the correct 20A plug.
This machine works on voltages from 208 to 440 V rms. Protected against overvoltage, the PULSEMIG will switch off
automatically.
DEVICES PRESENTATION (FIG 1)
1
S buttons
9
SD card support
2
Reel support
10
ON / OFF switch
3
Standard/Push Pull torch connector
11
Power supply cable
4
Earth clamp connector
12
Torch support
5
Push Pull torch command connector
13
Standard/Push Pull torch gas connector
6
SpoolGun torch command connector
14
Standard/SpoolGun torch gas connector
7
Standard/SpoolGun torch power connector
15
Bottle support (max 2*4m3 bottles)
8
Rocker switch Wire inch / Gas purge
16
Back cable support
SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE)
This device can weld 0.6/0.8/1 mm steel wires and 0.8/1 mm stainless steel wires.
The machine is delivered with Ø 0.8/1 rollers for steel and stainless steel welding. The value visible on the roller when
in place, is the wire diameter currently in use (FIG-3-B).
For Steel or Stainless Steel, you will need to use specific gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary
depending on usage. For the specific requirements, seek advice from your gas distributor.
The gas flow for steel is between 8 and 15L / min depending on the environment.
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)
This device can weld 0.8/1/1.2 mm aluminium wires.
To weld aluminium, neutral gas “pure Argon” (AR) is required. When choosing gas, ask a gas distributor for advice. The
gas flow in aluminium should be between 15 and 25 L / min depending on the environment.
Things to note when welding with Aluminium
- Rollers: Use rollers specific to aluminium welding (U groove)