iMotion SC111 User Manual Download Page 65

Page: 65 / 260

iWaylink Inc.

3-18 Aimer Delay

The aimer delay allows a delay time for the operator to aim the scan engine

before the picture is taken. Use these codes to set the time between when the

trigger is pulled and when the picture is taken. During the delay time, the

aiming light will appear, but the LEDs won’t turn on until the delay time is over.

Default = Off

200 milliseconds

400 milliseconds

Off(No display)

3-18-1 User-Specified Aimer Delay

If you want to set your own length for the duration of the delay, scan the

barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the

Programming Chart inside the back cover of this manual, then scan Save.

Delay Duration

Summary of Contents for SC111





































































































































































































































































Search results

Summary of Contents for SC111

Reviews:

Brands by name

Popular brands

iMotion SC111, User Manual

Search results

Summary of Contents for SC111

Reviews:

Brands by name

Popular brands