background image

Ilumen 

 

4

 

Installation Manual Ilumen PIDbox Light v1.2 

1

 

I

NFORMATION ON THIS MANUAL

 

This manual contains instructions on how to install the Ilumen PIDbox Light. 

1.1

 

V

ALIDITY

 

This manual applies to the Ilumen PIDbox Light. 

1.2

 

T

ARGET GROUP

 

This manual is intended for skilled persons. Only qualified persons with the appropriate skills 
are allowed to perform the tasks set forth in this manual. 

1.3

 

A

DDITIONAL INFORMATION

 

Links to additional information can be found at www.ilumen.be 

 

Ilumen PIDbox Light datasheet 

 

What is PID? 

 

PID checker 

1.4

 

S

YMBOLS

 

Symbol 

Explanation 

 

Indicates a hazardous situation which, if not avoided, will result in 
property damage 

 

Indicates a hazardous situation which, if not avoided, will result in 
death or serious injury 

 

Information that is important for a specific topic or objective, but is not 

safety-relevant 

2

 

S

AFETY

 

2.1

 

A

PPROPRIATE USAGE

 

The Ilumen PIDbox Light applies a voltage to PV modules in reference to earth. The device may 
only be switched on when the installation is done as described in this manual. 

Before installing the Ilumen PIDbox Light, ensure that the permitted operating range of each 
component is maintained at all times. 

Before using the Ilumen PIDbox Light you have to obtain the appropriate approval from the 
manufacturer of the PV modules and inverter. 

Any applications other than those described here shall be considered contrary to the 
appropriate usage. Alternative use or modification of the Ilumen PIDbox Light will void warranty 
claims and operation permit. 

 

 

Summary of Contents for PIDBOX





















Reviews: