manualshive.com logo in svg

illumina Infinium HD Super Assay, Reference Manual, Page: 64 / 79

Share
Download
illumina Infinium HD Super Assay Reference Manual Download Page 64

A

One stripe is visible between the first clamp and the alignment bar.

B

Glass back plate pressed against alignment bar.

C

Stripes are not visible between the second clamp and the barcode.

9

Remove the assembled flow-through chamber from the alignment fixture.

10 Starting at the nonbarcode end, trim the spacers from each end of the assembly using scissors.

A

Trimming the spacer at the nonbarcode end.

B

Trimming the spacer at the barcode end.

11 Leave assembled flow-through chambers on the lab bench in a horizontal position until ready to load onto

chamber rack in the

Extend and Stain BeadChips

step.

u

Do not place on absorbent paper.

u

Do not place in the chamber rack until instructed to do so.

12 Wash the hybridization chamber reservoirs with DI H

2

O.

Immediate and thorough washing ensures complete removal of PB1 from the wells.

Extend and Stain BeadChips

This step washes unhybridized and nonspecifically hybridized DNA samples from the BeadChips, adds
labeled nucleotides to extend primers hybridized to the sample, and stains the primers. After the flow-
through chambers are disassembled, the BeadChips are coated for protection.

Document # 11322427 v03

For Research Use Only. Not for use in diagnostic procedures.

58

Infinium HD Super Assay Reference Guide

Summary of Contents for Infinium HD Super Assay
















































































Reviews:

No comments