background image

Using as a 

juggling ball

https://youtu.be/bdTwNxUv218

Ignis BubblePoi can be also used as 
juggling balls. For this, just disconnect the 
cord – pull the cord hard, the cord will go 
out of the ball. To attach the cord, lean 
the low tip of the cord on some hard 
surface and press the poi, holding the 
hole against the bearing. 

Charging

When the poi is on charge, the red light slowly moves towards 
the top. When the poi is completely charged, the light finally 
turns green.

Lithium batteries don’t have a memory effect, that is why we recommend to charge the poi 
every time after using them; don’t wait till they are totally discharged. If you charge the poi every 
time, it makes the lifetime of the battery longer.

Avoid deep discharge of your digital poi! Otherwise, it may result in loss of battery capacity and 
reduction of working time.

Blue background of the submenu shows the total number of points in it.

To charge the Bubblepoi plug them to 
USB-charger or computer – you will see 
a red light. You can see the level of 
charge by position of the red light. The 
level of charge corresponds to it’s 
position. If in the middle, the poi is 50% 
charged, if almost on top – it refers to 
90%, etc. On the figure below the 
position of the red light roughly shows 
30% charge.

Summary of Contents for BubblePoi













Reviews: