22
en
STERYLIS ULTRA Operating Manual
“O
3
sterilisation – manual” mode
To start the „O3 sterilisation” mode in automatic mode press and hold the PROG.SET button in the „O3
sterilisation” section of the user panel. Enter the correct access code to enter manual mode.
Entering the access code:
The 4-digit code entered is shown on the display under „O3 sterilisation”. The „+” and „-” buttons
change the value by 1 active digit. An active number is the one that flashes at a high frequency, inactive
numbers light up constantly. The „PROG.SET” button changes the active digit to the next one on the right.
After entering the correct code, confirm it by pressing the yellow button „START” longer. If the code is
incorrectly entered, the code „XXXX” or „HHHH” will be displayed and a short beep will occur. In this case,
the code must be re-entered.
After approving a correctly entered code, the sterilisation process parameters must be completed.
The display in the „O3 sterilisation” section will show one of the following programs: “SEt.1”, “SEt.2” or
“SEt.3”. These are three different options for setting the parameters of the selected mode available to the
user.
To select one of the above mentioned settings, press the „+” button or the „-” button in the “O3
sterilisation” section to scroll up or down the setting selection accordingly.
The settings of the currently selected program will be displayed in the „O3 Concentration” and
„Ozone time” sections. To change the settings of the preset ozone concentration, control the „+” and
„-” buttons in the „O3 concentration” section to increase or decrease the value of the active digit by 1
respectively. The active digit is changed using the „SET” button. To change the setting of the preset ozone
time, control the „+” and „-” buttons in the „ozone time” section to increase or decrease the value of the
active digit by 1 respectively. The active digit is changed using the „SET” button.
To save the settings for a given program, press and hold the „PROG.SET” button in the „O3
sterilisation” section. Save of the settings will be confirmed by a short beep and a single blinking of the
concentration and time displays.
To save the settings of all programs and to proceed directly to the sterilisation process, press and
hold the yellow „START” button in the „O3 sterilisation” section. The display in the „O3 sterilisation”
section will show the selected type of sterilisation, the display in the „Ozone time” section will start
counting down the time remaining until the start of sterilisation and the „O3” and „!” warnings will start
blinking.
After the 60-second countdown, the unit will check the proper functioning of the relevant actuators
and then the ozone generators will start and the unit will operate in the selected mode of operation. If any
errors are detected, the unit will go into standby mode and display the corresponding error codes on the
display in the „STERILISATION” section.
When the device is in sterilisation mode, an additional acoustic signal is activated (can be
deactivated according to the instructions in 6.4) and a flashing signal generated by the warning beacon.
When the safe ozone concentration (0.1 ppm) is exceeded, the safe ozone concentration indicator will stop
illuminating.
The sterilisation process or the countdown to the start of sterilisation can be interrupted at any
time by pressing any button on the user panel. The parameter settings for the relevant programs can be
interrupted by pressing the „START” button for any of the other operating modes. The device will then go
into standby mode.
During the TS phase, the display in the „Ozoning time” section will indicate the set ozoning time,
during To phase the set ozoning time will be counted down and during the TD phase the time „00:00” will
be displayed. This informs the user about the phase of the sterilisation process.
After completion of the sterilisation process, the device will switch off the ozone generators
and switch on the UV-C fluorescent tubes to accelerate the ozone decomposition. When the safe
concentration (0.1 ppm) is reached, the ozone safety light will light up.
Summary of Contents for STERYLIS ULTRA-220
Page 2: ......
