manualshive.com logo in svg

IFM SM6x04, Operating Instructions Manual

Share
Download
IFM SM6x04 Operating Instructions Manual Download Page 17

17

UK

10.1  Parameter setting in general

1�  Change from the RUN mode to the main menu and 

selection of the requested parameter 

[Mode/Enter] 

2�  Acknowledge the set parameter value

[Set]

3�  Change the setting mode

[Set] > 5 s

4�  Modification of the parameter value

 -incrementally by pressing once

 -continuously by keeping the button pressed

To reduce the value: let the display move to the 

maximum setting value� Then the cycle starts 

again at the minimum setting value�

[Set]

5�  Acknowledge the set parameter value

[Mode/Enter]

6�  Return to the RUN mode

> 30 seconds (timeout) 

or

[Mode/Enter] until the RUN 

mode is reached�

10.1.1  Change to the menu "Extended functions"

1�  Change from the RUN mode to the main menu and 

selection of the parameter EF

[Mode/Enter] 

2�  Change to sub-menu EF

[Set]

10.1.2  Locking / Unlocking

The unit can be locked electronically to prevent unintentional settings� On delivery: 

not locked�

Locking

 

►

Make sure that the unit is in the normal operating mode�

 

►

Press [Mode/Enter] and [Set] simultaneously for 10 s until [Loc] is 

displayed�

Unlocking

 

►

Make sure that the unit is in the normal operating mode�

 

►

Press [Mode/Enter] and [Set] simultaneously for 10 s until [uLoc] is 

displayed� 

Summary of Contents for SM6x04























Reviews:

No comments

Brands by name

Popular brands

Load more brands