manualshive.com logo in svg

IFM efector100 G1503S, Operating Instructions Manual, Page: 7 / 47

Share
Download
IFM efector100 G1503S Operating Instructions Manual Download Page 7

7

UK

4.1  Requirements for the hardware configuration

The following requirements must be complied with when using the safety relay 

G1503S:

4.1.1  Product-independent requirements

It must be ensured that the safety requirements of the respective application 

correspond to the requirements stated in these instructions�
The specified technical data indicated in these instructions must be complied with� 

The principle of normally closed operation must be applied to all external safety 

circuits connected to the system�
The safety relays type G1503S in operation have to be subjected to a self-test 

(switching off) within a period of maximum 12 months�
The self-test can be carried out by switching the supply voltage off and on or by a 

safety request�

4.1.2  Product-dependent requirements

In case of faults within the safety relay which result in the defined safe state, the 

safety relay must be replaced�
Any faulty unit should be returned to the manufacturer�

Summary of Contents for efector100 G1503S
















































Reviews:

No comments