IFM ecomatDisplay CR1077 Operating Instructions Manual Download Page 13 | Manualshive

Page: 13 / 23

background image

CR1077

13

38 (1,5")

56

62

6

Fig. 10: Mounting plate with ball head

38,1

30

5,3

Fig. 11: Hole dimensions

Tightening torque: 5

±0.5

Nm

u

Slightly loosen the fastening screw of the mounting arm.

u

Place the mounting arm onto the ball heads and tighten the fastening screw.

4.5 Other installation types

Permissible installation types:

Panel mounting / control cabinet installation (

Surface mounting with RAM® mount system (

All other installation types are in the sole responsibility of the system creator.

«
...
11
12
13
14
15
...
»

Summary of Contents for ecomatDisplay CR1077
























Reviews:

No comments

Related manuals for ecomatDisplay CR1077

Brand: Rayrun Pages: 2

Brand: IDenticard Pages: 2

Brand: 3Ware Pages: 2

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: FEAS Pages: 4

CIATControl OPC Server

Brand: CIAT Pages: 32

Brand: Danfoss Pages: 8

Infi 90 IMAOM01

Brand: Bailey Pages: 44

CentralControl CC41

Brand: Becker Pages: 48

Brand: GSK Pages: 32

F&G Xcomfort CRCA-00/02

Brand: Moeller Pages: 4

Brand: Rabbit Pages: 12

Brand: e-survey Pages: 12

XBee DigiMesh 2.4

Brand: Digi Pages: 157

Brand: Instrutech Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands