IFM ECOMAT 300 AL1000 Device Manual Download Page 33

Page: 33 / 61

IO-Link master

Data storage

Deactivated and deleted

The data storage mechanism is deactivated and

the master deletes all stored parameters for the

respective port�

The data storage mechanism is supported from IO-Link specification v1�1� Both the IO-Link master and the

device must support at least IO-Link v1�1�

Device parameters

(DPP2)

Byte 10

hex

�� Byte1F

hex

The device parameter page 2 describes the area

between the IO-Link objects 10

hex

�� 1F

hex

� This

is the manufacturer-specific area of the IO-Link

device data�

The data is optionally provided by IO-Link

devices and can be read and written by the

master�

17 I&M functions

The ProfiNet device supports Identification & Maintenance functions (I&M)� The

general Identification & Maintenance functions 0 to 4 can be read via slot 0� IO-

Link specific Identification & Maintenance functions 0, 16 �� 23 and 99 can be read

via slot 1 and subslot 1�

Slot 0 and slot 1 have their own I&M function (I&M 0)�

I&M 0 (slot 0)

I&M data

Access / data type

Presets

MANUFACTURER_ID

Read / 2 bytes

hex

ORDER_ID

Read / 20 bytes

2701513

SERIAL_NUMBER

Read / 16 bytes

Defined in the production process

HARDWARE_Revision

Read / 2 bytes

Corresponds to the hardware

revision of the device

SOFTWARE_REVISION

Read / 4 bytes

Corresponds to the firmware

revision of the device

REVISION_Counter

Read / 2 bytes

0000

hex

(reserved)

PROFILE_ID

Read / 2 bytes

F600

hex

(generic device)

PROFILE_SPECIFIC_TYPE

Read / 2 bytes

0003

hex

(I/O modules)

IM_VERSION

Read / 2 bytes

0101

hex

(version 1�1)

IM_SUPPORTED

Read / 2 bytes

001E

hex

(I&M 1��4)

Summary of Contents for ECOMAT 300 AL1000






























































Search results

Summary of Contents for ECOMAT 300 AL1000

Reviews:

Related manuals for ECOMAT 300 AL1000

Brands by name

Popular brands

IFM ECOMAT 300 AL1000, Device Manual

Search results

Summary of Contents for ECOMAT 300 AL1000

Reviews:

Related manuals for ECOMAT 300 AL1000

Brands by name

Popular brands