IFM ECOMAT 300 AL1000 Device Manual Download Page 25

Page: 25 / 61

IO-Link master

Designation

Colour

Meaning

State

Description

RDY

Green/ yel-

low / red

Ready

Green ON

Device is ready for operation

Yellow

flashing

Firmware update is being performed

Green / yel-

low flashing

Overvoltage or undervoltage at U

Temperature of the device is in the critical

area

Failure of the actuator supply U

and red U

LED:

sensor supply overload

OFF

Device is not ready for operation

Red

Bus Fault

Red ON

No link status available on any port

Red flashing

SF LED not flashing: Link status available,

no communication connection to the Profi-

Net controller

Red flashing

SF LED flashing: hardware watchdog has

been triggered

Red

Off

A ProfiNet controller has established an

active communication connection to the

ProfiNet device

Red

Station Fail

Red ON

ProfiNet diagnostics available

Red flashing

Flashes only together with the BF LED;

watchdog triggered

Red OFF

ProfiNet diagnostics not available

Green /

red

sensors

Green ON

Communications power/sensor voltage

present

OFF

Communications power/sensor voltage not

present or too low

Red ON

Sensor voltage overload

Green

actuators

Actuator voltage present

OFF

Actuator voltage not present

Summary of Contents for ECOMAT 300 AL1000






























































Search results

Summary of Contents for ECOMAT 300 AL1000

Reviews:

Related manuals for ECOMAT 300 AL1000

Brands by name

Popular brands

IFM ECOMAT 300 AL1000, Device Manual

Search results

Summary of Contents for ECOMAT 300 AL1000

Reviews:

Related manuals for ECOMAT 300 AL1000

Brands by name

Popular brands