IFM DTM426 Operating Instructions Manual Download Page 7 | Manualshive

Page: 7 / 22

background image

DTM426 DTM427

7

5 Function

5.1 ID tags

are passively operated without a battery. The energy required for operation is provided by

the read/write head.

The energy is provided via an inductive coupling. The integrated antenna coil in the read/write head
generates a magnetic field which partly penetrates the antenna coil of the ID tag. A voltage is
generated by induction that supplies the data carrier with energy.

The device supports ID tags according to ISO 15693.

5.2 Device overview

DTM426

Article number:

DTM426

Function:

Read/write head

Type designation:

DTMHF GBRWCJUS03

Type:

M18, flush mountable

DTM427

Article number:

DTM427

Function:

Read/write head

Type designation:

DTMHF GNRWCJUS03

Type:

M18, non flush mountable

«
...
5
6
7
8
9
...
»

Summary of Contents for DTM426























Reviews:

No comments

Related manuals for DTM426

Brand: Data Aire Pages: 28

PROX-BOOSTER 2G

Brand: Nedap Pages: 25

Brand: PURE Pages: 88

Brand: jablotron Pages: 3

Brand: Mortuary Lift Pages: 6

Devicenet R7F4DD-DA16A-H

Brand: M-system Pages: 7

Marine Pro RIO 216

Brand: auto maskin Pages: 11

RaptorX-SL1200-S15

Brand: CNC-Step Pages: 102

Brand: Sel Pages: 12

Brand: Zenith Pages: 20

Brand: WAGO Pages: 12

Brand: Daewoo Pages: 29

Brand: WALTCO Pages: 44

Brand: National Instruments Pages: 173

Brand: Exibel Pages: 84

Brand: JVC Pages: 36

Brand: JVC Pages: 74

Brand: Philips Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands