IFM AC1401/02 Device Manual Supplement Download Page 13

Page: 13 / 123

ifm

Device Manual Supplement: Acyclic data records and Command interface (AC14 and AC4S)

2017 / 09

Acyclic data records

3.3.1

AS-i master status flags

7160

The AS-i master status flags provide information about the status of the AS-i master. After a status
change, the AS-i master immediately updates the flags.

The AS-i master status flags are saved in the following register:

AS-i master status flags

ECPS

ECP

–

WCD

–

HWDT

SER

HER

Legend:

Flag

Designation

Description

Initial value at power-on

HER

Hardware Error

1 (TRUE): a hardware error occurred during the power-on

self test

0 (FALSE)

SER

Software Error

1 (TRUE): Software error occurred:

Stack Overflow, Stack Underflow, Undefined
Opcode, Instruction Fault, Illegal Access,
Watchdog Timeout

0 (FALSE)

HWDT

Host Watchdog
Timeout

1 (TRUE): Host watchdog not triggered by the host within

200 ms; master changed to the offline mode

0 (FALSE)

Configuration Missing

1 (TRUE): Configuration not yet fully received from the host.

Becomes FALSE as soon as PCD, PP and LPS
have been set

1 (TRUE)

WCD

Watchdog Control
Disabled

1 (TRUE): Signals the host that the watchdog signal is not

processed in the master.

0 (FALSE)

ECP

Execution Control
Phase

Display of the different phases the execution control goes
through during boot (

→ table).

ECPS

Execution Control
Phase State

Display of the substates of the different execution control
phases (

→ table).

Execution Control Phase

Execution Control Phase State

0 = inactive

–

1 = start phase

0 = master start and initialisation
1 = wait for configuration
2 = wait for start

2 = reserved

–

3 = offline phase

–

4 = detection phase

–

5 = activation phase

–

6 = normal operation

0 = normal data exchange
1 = slave finder activated

Summary of Contents for AC1401/02




























































































































Search results

Summary of Contents for AC1401/02

Reviews:

Related manuals for AC1401/02

Brands by name

Popular brands

IFM AC1401/02, Device Manual Supplement

Search results

Summary of Contents for AC1401/02

Reviews:

Related manuals for AC1401/02

Brands by name

Popular brands