IFM Electronic SM9000 Operating Instructions Manual Download Page 42

Page: 42 / 44

11.3 Error indications

Warning message

[SC1]

Short circuit in OUT1�

LED8 for OUT1 flashes (→ 7 Operating and display elements).

[SC2]

Short circuit in OUT2�

LED7 for OUT2 flashes (→ 7 Operating and display elements).

[SC]

Short circuit in both outputs�

LED7 and LED8 flash (→ 7 Operating and display elements).

[OL]

Detection zone of volumetric flow or temperature exceeded�

[UL]

Below the detection zone of volumetric flow or temperature�

[Err]

•

Unit faulty / malfunction�

•

Measured value outside the detection zone�

[C�Loc]

Setting pushbuttons locked, parameter change rejected�

Active IO-Link communication�

[S�Loc]

Setting pushbuttons locked, parameter change rejected�

Unlock using parameter setting software�

[SEnS]

Sensor signal invalid�

•

Measuring pipe not sufficiently filled�

•

Medium with too low a conductivity�

[IOE�n]

Malfunctioning� The unit is faulty and must be replaced�

12 Technical data

Technical data and scale drawing at www.ifm.com → Data sheet search → Enter

the article number�

Summary of Contents for SM9000













































Search results

Summary of Contents for SM9000

Reviews:

Related manuals for SM9000

Brands by name

Popular brands

IFM Electronic SM9000, Operating Instructions Manual

Search results

Summary of Contents for SM9000

Reviews:

Related manuals for SM9000

Brands by name

Popular brands