IFM Electronic OPD100 Operating Instructions Manual Download

Page: 34 / 39

[Language]

Select the menu language

►

Confirm the parameter with [ENTER] and select one of the

options using the [Up] or [Down] button�

►

Confirm your selection by pressing [ENTER]�

> The menu language is confirmed�

[Back]

Finish parameter setting

►

Confirm the parameter with [ENTER]�

> Display changes to [Display]�

12 IO-Link

12.1 General information

This unit has an IO-Link communication interface which requires an IO-Link-

capable module (IO-Link master) for operation�

The IO-Link interface enables direct access to the sensor values and parameters

and provides the possibility to set the parameters of the unit during operation�In

addition, communication is possible via a point-to-point connection with a USB

adapter cable�
You will find more detailed information about IO-Link at www�ifm�com�

12.2 Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link unit and

detailed information about sensor values, diagnostic information and parameters

in the overview table at www�ifm�com�

12.3 Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�ifm�com�

12.4 Functions

With IO-Link all functions and measured data are available that can also be

accessed via the display and pushbuttons on the unit�
All functions are described in detail in the IODD�

Summary of Contents for OPD100








































Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands

IFM Electronic OPD100, Operating Instructions Manual

Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands