IFM Electronic OPD100 Operating Instructions Manual Download

Page: 33 / 39

[Output Function]

Setting of the switching function for OUT1

►

Confirm the parameter with [ENTER] and select one of the

options [High active] / [Low active] using the [Up] or [Down]

button�

►

Confirm your selection by pressing [ENTER]�

> The output function for OUT1 is confirmed�

High active: OUT1 is switched on

if matching value > switching threshold�

Low active: OUT1 is switched on

if matching value < switching threshold�

In the trigger mode [CONT], OUT2 is automatically set as

complementary switching output to OUT1�

[Output Logic]

Set the switching logic for all inputs and outputs

►

Confirm the parameter with [ENTER] and select one of the

options [PNP] / [NPN] using the [Up] or [Down] button�

►

Confirm your selection by pressing [ENTER]�

> The switching logic is confirmed�

[Back]

Finish parameter setting

►

Confirm the parameter with [ENTER]�

> Display changes to [Configuration]�

11.2.2 Submenu [Display]

[Brightness]

Set display brightness

►

Confirm the parameter with [ENTER] and select one of the

options [ON] / [OFF] using the [Up] or [Down] button�

►

Confirm your selection by pressing [ENTER]�

> The display brightness is confirmed�

[Colour]

Set display colour for the matching value

►

Confirm the parameter with [ENTER] and select the desired

option using the [Up] or [Down] button�

►

Confirm your selection by pressing [ENTER]�

> The display colour for the matching value is confirmed�

Options

G1ou: green = good part

r1ou: red = good part

white: matching value always white

red: matching value always red

green: matching value always green

Summary of Contents for OPD100








































Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands

IFM Electronic OPD100, Operating Instructions Manual

Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands